SR-16-008 – HID HEADLAMP HORIZONTAL ADJUSTMENT LOCKING CLIPS NOT SECURED – 2017 Mitsubishi Mirage

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA Campaign Number: 16V675
Component(s): EXTERIOR LIGHTING
Potential Number of Units Affected: 587

Manufacturer: Mitsubishi Motors North America, Inc.

 

SUMMARY:

Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2017 Mirage vehicles manufactured October 28, 2015, to August 4, 2016 and equipped with High Intensity Discharge (HID) headlamps. The affected vehicles may have been assembled without the headlight horizontal adjustment lockout clips properly secured.

As such, these vehicles fail to comply with the requirement of Federal Motor Vehicle Safety Standard (FMVSS) number 108, “Lamps, Reflective Devices, and Associated Equipment.”

 

CONSEQUENCE:

Without the horizontal adjustment locking clip being secured, the headlight can be adjusted to either reduce the driver’s visibility or blind oncoming vehicles. Both conditions can increase the risk of a crash.

 

REMEDY:

MMNA will notify owners, and dealers will secure the horizontal locking clips as necessary, free of charge.

The manufacturer has not yet provided a notification schedule.

Owners may contact MMNA customer service at 1-888-648-7820.

MMNA’s number for this recall is SR-16-008.

 

NOTES:

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Mitsubishi has a Recall

 

SUBJECT:

HID HEADLAMP HORIZONTAL ADJUSTMENT LOCKING CLIPS NOT SECURED – SAFETY RECALL CAMPAIGN

No: SR-16-008
DATE: September, 2016
MODEL: 2017 Mirage

 

PURPOSE

This bulletin provides directions for inspection of and securing of the HID headlamp horizontal adjustment locking clips on affected vehicles.

 

BACKGROUND

The High Intensity Discharge (HID) headlamps allow for horizontal adjustment during the vehicle assembly process. After assembly, horizontal adjustment locking clips are secured so that no further adjustments can be made. However, HID headlamps on certain ’17 Mirage vehicles were inadvertently shipped without the horizontal adjustment locking clips being secured. This is a non-compliance with FMVSS 108. Without the horizontal adjustment locking clip being secured, the headlight can be adjusted to either reduce the driver’s visibility or blind oncoming vehicles. Both conditions can increase the risk of a crash.

 

AFFECTED VEHICLES

2017 Mirage (hatchback) with HID headlamps.

Important

 

REQUIRED EQUIPMENT

  • Flashlight
  • Phillips screwdriver

 

INSPECTION AND REPAIR PROCEDURE

  1. Use the engine hood release lever (located under the instrument panel near the driver’s door) to unlock the engine hood. Pull the lever toward you to release the engine hood latch.

engine hood release lever

  1. Release the lever and lift the engine hood.

Release the lever

  1. Support the engine hood with the hood prop. Insert the hood prop securely in the opening under the hood marked with an arrow.

engine hood

  1. Locate the driver’s side HID headlamp horizontal adjustment locking clip.

HID headlamp horizontal adjustment locking clip

 

HID headlamp horizontal adjustment locking clip

HID headlamp horizontal adjustment locking clip HID headlamp horizontal adjustment locking clip

  1. If HID headlamp horizontal adjustment locking clip is secured, proceed to step 5.
  2. If NG condition is found (HID headlamp horizontal adjustment locking clip not secured), take a photo of NG condition for posting to Photos Required Condition (PRC) system, then fold the tab over against the lamp housing using a Phillips screwdriver until you hear a “click” as it locks into place.

HID headlamp horizontal adjustment locking clip

  1. Locate the passenger’s side HID headlamp horizontal adjustment locking clip.

HID headlamp horizontal adjustment locking clip

  1. If HID headlamp horizontal adjustment locking clip is secured, proceed to step 6.
  2. If NG condition is found (HID headlamp horizontal adjustment locking clip not secured), take a photo of NG condition for posting to Photos Required Condition (PRC) system, then fold the tab over against the lamp housing using a Phillips screwdriver until you hear a “click” as it locks into place.

HID headlamp horizontal adjustment locking clip

  1. Close the hood.
  2. If photo(s) were taken of a horizontal adjustment locking clip not secured, submit photo(s) to MMNA PRC.

 

PARTS INFORMATION

No parts required to complete this procedure.

 

WARRANTY INFORMATION

There are 3 possible repair scenarios for this campaign.

# Repair Procedure Campaign Operation Labor Time
Allowance
1 Inspect both front headlamps – 2 clips OK C1610M01 0.2 hrs.
2 Inspect both front headlamps – 1 clip OK – 1 not secured

(Photo submission to PRC required.)

C1610M02 0.3 hrs.
3 Inspect both front headlamps – 2 clips not secured

(Photos submission to PRC required.)

C1610M03 0.3 hrs.

 

WARRANTY / RECALL CAMPAIGN CLAIM INFORMATION

Enter all claims as claim type ‘C’ – Recall/Campaign Claims.

Please follow the campaign instructions when entering each claim in order to select the applicable operation code that correctly matches up with the work that was actually performed. A claim example is provided below.

Certain 2017MY Mirage models with HID headlamps.

 

Claim Header Section:

Claim Header Section

After entering the required customer data, vehicle information, selecting the applicable repair campaign and scenario performed (please note there are 3 possible repair scenarios for this campaign), and then hitting the “Save and Continue” button, the system will automatically fill-in several fields. See the labor examples on the next page. Scenarios 2 and 3 both require photos to be taken of headlamp aiming clips found to have NOT been secured (refer to TSB procedures). NO PARTS ARE NEEDED.

 

LABOR:

There are 3 possible repair scenarios for this campaign. You may only select 1 scenario.

Scenario 1 Inspect both front headlamps – 2 clips OK C1610M01 0.2 hrs.
Scenario 2 Inspect both front headlamps – 1 clip OK – 1 not secured

(Photo submission to PRC required.)

C1610M02 0.3 hrs.
Scenario 3 Inspect both front headlamps – 2 clips not secured

(Photos submission to PRC required.)

C1610M03 0.3 hrs.

 

NOTE: Be sure to take photos of the still open tabs BEFORE you close them. Post photos to the PRC in the RECALL PHOTO DOCS SUPPORT category.

RECALL PHOTO DOCS SUPPORT

 

PARTS:

No parts are required for this recall.

 

 

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [371.23 KB]

 

 

Leave a Comment

Share to...